Monday, January 25, 2016

How to Develop Slide Film

The hardware and the chemicals necessary for developing slide film (often referred to as E6) are readily available from any photo store--if no such stores are available locally, all of your supplies can be purchased online. You will need a room with a sink and counter space and the items listed here. Then follow these steps to develop slide film.

Instructions

    1

    Set your plastic or metal film reel to the right size for your film. Move one end of the reel along the central hub until it clicks into place at the right size.

    2

    Set out the following items in your darkroom or place them inside your changing bag: the canister of film, a church key bottle opener (or you can purchase a special film canister opener), the plastic or steel film reel which you have previously set to the correct size, your plastic film developing tank and a pair of scissors.

    3

    Open the flat end of the film canister using your church key or a specialized film canister opener. This step must be done in total darkness. Remove the film and its small reel. Only touch the edges of the film with your fingers. Locate the lead end of the film and cut it square with your scissors.

    4

    Thread film into the opening of the film reel. Then, holding one reel in each hand, gently twist the reels back and forth in opposite directions while using the tips of your fingers to gently guide the film as it winds itself smoothly onto your film reel. This requires some practice. Work slowly so that your film does not bind and winds easily onto your reel. When the film is loaded onto the reel cut the end of the film free of its spool.

    5

    Place the reel into the film tank and tighten the lid of the tank.Turn on the lights or remove the film tank from the changing bag.

    6

    Mix your chemicals carefully, following instructions from the kit. Only mix as much as you need. Label not only your bottles but the bottle caps as well. It is vital that the color developer (the second developer) not contaminate your first developer at all. Even accidentally switching bottle caps could be disastrous.

    7

    Place your bottles of chemicals as well as your film tank into your water bath tray. Set the temperature to precisely 38 degrees Celsius. Leave all of your chemicals as well as your film tank in the water bath until they come up to the proper temperature. Use a color film thermometer to double check that the water and your chemicals have reached precisely 38 degrees.

    8

    Pour the developer into your tank and start your timer. Different tanks require differing amounts of developer so read the manufacturer's instructions and pour in the proper amount. Agitate the tank every fifteen seconds to prevent bubbles from forming on your film and destroying your work. Unless otherwise instructed, leave the developer in the tank for precisely 6 minutes. Just before the 6 minutes are up dump your developer back into the developer bottle and at precisely 6 minutes pour your bottle of 38-degree water into your tank. Agitate the tank for two minutes, then pour out the water. Add water a second time, agitate and pour out the water.

    9

    Pour the color developer into the tank and start timing. Agitate every 15 seconds for precisely 6 minutes. Pour color developer back into its marked bottle and rinse your developer tank with mildly warm water for two minutes. The temperature of the water is no longer critical.

    10

    Add the bleach/fix mixture to the tank and agitate every 15 seconds for 6 minutes. Pour the bleach/fix mixture back into its bottle and then rinse the development tank with warm water for 4 minutes.

    11

    If you are using a stabilizer add it to your tank and agitate for 1 minute. Pour it back into its bottle and then rinse your tank for 2 minutes with warm running water.

    12

    Open the tank and very carefully remove the film reel. Use a clothespin or a special film clip to clip the end of the film to a line so it can hang freely to dry. Clip a small weight to the bottom end of the film to keep it straight while drying. Once dry your film can be cut and the individual images mounted in cardboard slide sleeves, which are readily available at any photo store.


The hardware and the chemicals necessary for developing slide film (often referred to as E6) are readily available from any photo store--if no such stores are available locally, all of your supplies can be purchased online. You will need a room with a sink and counter space and the items listed here. Then follow these steps to develop slide film.

Instructions

    1

    Set your plastic or metal film reel to the right size for your film. Move one end of the reel along the central hub until it clicks into place at the right size.

    2

    Set out the following items in your darkroom or place them inside your changing bag: the canister of film, a church key bottle opener (or you can purchase a special film canister opener), the plastic or steel film reel which you have previously set to the correct size, your plastic film developing tank and a pair of scissors.

    3

    Open the flat end of the film canister using your church key or a specialized film canister opener. This step must be done in total darkness. Remove the film and its small reel. Only touch the edges of the film with your fingers. Locate the lead end of the film and cut it square with your scissors.

    4

    Thread film into the opening of the film reel. Then, holding one reel in each hand, gently twist the reels back and forth in opposite directions while using the tips of your fingers to gently guide the film as it winds itself smoothly onto your film reel. This requires some practice. Work slowly so that your film does not bind and winds easily onto your reel. When the film is loaded onto the reel cut the end of the film free of its spool.

    5

    Place the reel into the film tank and tighten the lid of the tank.Turn on the lights or remove the film tank from the changing bag.

    6

    Mix your chemicals carefully, following instructions from the kit. Only mix as much as you need. Label not only your bottles but the bottle caps as well. It is vital that the color developer (the second developer) not contaminate your first developer at all. Even accidentally switching bottle caps could be disastrous.

    7

    Place your bottles of chemicals as well as your film tank into your water bath tray. Set the temperature to precisely 38 degrees Celsius. Leave all of your chemicals as well as your film tank in the water bath until they come up to the proper temperature. Use a color film thermometer to double check that the water and your chemicals have reached precisely 38 degrees.

    8

    Pour the developer into your tank and start your timer.

    Enhance your photography skill,The Top Secret Photography Techniques

    . Different tanks require differing amounts of developer so read the manufacturer's instructions and pour in the proper amount. Agitate the tank every fifteen seconds to prevent bubbles from forming on your film and destroying your work. Unless otherwise instructed, leave the developer in the tank for precisely 6 minutes. Just before the 6 minutes are up dump your developer back into the developer bottle and at precisely 6 minutes pour your bottle of 38-degree water into your tank. Agitate the tank for two minutes, then pour out the water. Add water a second time, agitate and pour out the water.

    9

    Pour the color developer into the tank and start timing. Agitate every 15 seconds for precisely 6 minutes. Pour color developer back into its marked bottle and rinse your developer tank with mildly warm water for two minutes. The temperature of the water is no longer critical.

    10

    Add the bleach/fix mixture to the tank and agitate every 15 seconds for 6 minutes. Pour the bleach/fix mixture back into its bottle and then rinse the development tank with warm water for 4 minutes.

    11

    If you are using a stabilizer add it to your tank and agitate for 1 minute. Pour it back into its bottle and then rinse your tank for 2 minutes with warm running water.

    12

    Open the tank and very carefully remove the film reel. Use a clothespin or a special film clip to clip the end of the film to a line so it can hang freely to dry. Clip a small weight to the bottom end of the film to keep it straight while drying. Once dry your film can be cut and the individual images mounted in cardboard slide sleeves, which are readily available at any photo store.



  • Martin Scorsese's Film School: The 85 Films You Need To See To ...

    www.fastcocreate.com/1679472

    Fast Companys in-depth profile of Martin Scorsese for the How To Live A Creative Life issue had a compelling by-product: this list of 85 films that the director ...


  • How to create a "My Map" in Google Maps - YouTube

    www.youtube.com/watch?v=TftFnot5uXw

    Go to Google Maps: http://maps.google.com Google Maps Playlist: http://www.youtube.com/view_play_list... How to create personalized, annotated ...


  • How to Lose Friends & Alienate People (2008) - IMDb

    www.imdb.com/title/tt0455538

    Sidney Young is a disillusioned intellectual who both adores and despises the world of celebrity, fame and glamor. His alternative magazine, "Post Modern Review ...


  • How to Create Your Own DIY Silent Retreat - 2. What to do

    www.think-happier.com/how-to-create-your-own-diy-silent-retreat-2...

    You can create your own silent retreat and enjoy the benefits of an expensive retreat. Find out what activities you can schedule for your home-made retreat.


  • Dr. Strangelove or: How I Learned to Stop Worrying and Love the ...

    www.imdb.com/title/tt0057012

    Paranoid Brigadier General Jack D. Ripper of Burpelson Air Force Base, he believing that fluoridation of the American water supply is a Soviet plot to poison the U.S ...


  • Support Prezi

    prezi.com/support

    Prezi is a cloud based presentation software that opens up a new world between whiteboards and slides. The zoomable canvas makes it fun to explore ideas and the ...


  • Howcast The best how-to videos on the web

    www.howcast.com

    Howcast is the best source for fun, free, and useful how-to videos and guides.


  • PhotoPeach - Fresh slideshows to go!

    photopeach.com

    Automatically make your own free slide show in seconds. Upload photos, pick music, add captions in the show, and more!


  • How to make a movie

    indiemoviemaking.com

    How to make a movie step by step. From writing a script to production to final movie distribution.


  • HOW TO videomapping.org - a blog for people interested in ...

    videomapping.org/?page_id=42

    Even if she was using a good camera in picture number 2 and a wide angle one from her phone in picture number 1 the object is not matching the beamer lens throw.


  • How To Be A Model Blog-

    www.howtobeamodelblog.com

    1) I cant smile on command. seriously? thats what modeling IS OR alternately I dont like my smile, so I dont smile in pictures.


  • Wiggio - Makes it easy to work in groups.

    wiggio.com

    Wiggio is a completely free, online toolkit that makes it easy to work in groups. With Wiggio you can: - keep shared calendar (with text message reminders) - poll ...


  • Online Self Improvement Course and Life Coaching

    lifeandself.com

    Our online self improvement course and life coaching course is packed full of positive psychology lessons in productivity, motivation, self help, depression, anxiety ...


  • Animoto - Pro Education - Animoto - Make & Share Beautiful

    animoto.com/pro/education

    Promote school events and marketing campaigns through video. Delight students, parents, alumni, your community, and donors with awesome videos that take minutes

  • How to use acrylic gels & mediums: Part 1 (video)

    willkempartschool.com/how-to-use-acrylic-mediums-without-ruining...

    Do you feel you should be using mediums? Youve probably brought a couple and had a play around, but are you using the right ones? Or is the overuse of mediums ...

  • FUJIFILM SeeHere

    www.seehere.com

    3D Printing Services Fujifilm continues to support 3D prints with a new website dedicated solely to your 3D printing needs. Uploading and ordering 3D prints has never ...

  • Wonder How To Show & Tell for Creators & Doers

    www.wonderhowto.com/following

    Wonderland for Your Inner Nerd. Create, Pontificate, & Receive Kudos for Sharing Your Mad Skills.

  • Digital Inspiration - Technology Blog

    www.labnol.org

    17 Jun 2013 Show How Busy you are with the Gmail Counter. This easy tutorial will help you create a real-time Gmail counter that will display the count of unread ...

  • How to make a BristleBot - Evil Mad Scientist Laboratories - YouTube

    www.youtube.com/watch?v=rUSTXUis_ys

    See http://www.evilmadscientist.com/article.php/bristlebot

  • Create timelines, share them on the web Timetoast timelines

    timetoast.com

    Timetoast is a place to create timelines that you can add to your blog or website. You can create historical timelines of important events, or build a timeline of ...

  • Money eHow UK - eHow How to Videos, Articles & More -

    www.ehow.co.uk/money

    Money: Find great tips on The worst jobs in the UK, Bizarre business names or what not to call yours and The 8 worst UK cities and towns to live in. Learn about ...

  • Log In Scribd

    www.scribd.com/login

    Use your Facebook login and see what your friends are reading and sharing.

1 comments:

  1. Order a professional Sparkling White Smiles Custom Teeth Whitening System online and get BIG SAVINGS!
    * 10 shades whiter in days!
    * Results Guaranteed.
    * Better than your dentist.
    * Same strength as dentists use.

    ReplyDelete